WhatsApp Maggie
Complete Pipe Extrusion Lines

China Pipe Extrusion Line Factory

One line, matched from the mixer to the last stacker. We build complete lines for HDPE and PE, PVC, PPR and MPP pipe, and for precision and medical tube, flexible hose, drinking straw and core tube, each sized to your material, diameter, wall thickness, output and end use, and run on your spec before shipment.

  • Factory built pipe extrusion lines
  • Trial run before shipment
  • Configuration based on pipe application
  • Overseas installation support
Chat With Maggie
Line At A Glance

16mm To 1200mm

Diameter span across our PVC, HDPE and PPR lines, from small tube up to large PE pipe.

HDPE, PVC, PPR, MPP

Your resin, your formulation and your share of recycled material decide the screw, die and cooling.

Configured And Trial Run

Wired for your local voltage and standard, and run on your own material before it leaves us.

01 / Pipe Line Selector

Start With The Pipe You Make

Find the pipe product closest to yours. The table names the line type and the points we confirm with you before any machine list is drawn up.

Your Pipe Product Suggested Line Key Points To Confirm
Water, gas, irrigation or cable duct pipe HDPE / PE Pipe Extrusion Line SDR, diameter range, cooling length, winder or cutter
Drainage pipe, pressure pipe or electrical conduit PVC Pipe Extrusion Line Filler ratio, PVC formulation, pipe size, belling need
Hot and cold water pipe PPR Pipe Extrusion Line OD tolerance, pipe weight, single or multi layer
Power cable protection pipe MPP Pipe Extrusion Line Wall thickness, haul off force, cooling capacity
Small industrial tube Precision Tube Extrusion Line OD and ID tolerance, concentricity, winding control
Medical tubing or catheter tube Medical Catheter Tube Extrusion Line Dimensional control, clean operation, documentation support
Soft hose or flexible tube Flexible Hose Extrusion Line Material type, flexibility, surface finish, winding tension
Small tube or drinking straw Small Tube / Drinking Straw Line Material choice, diameter, cutting length, production speed
Plastic winding core tube Core Tube Extrusion Line Straightness, rigidity, cut accuracy, ID and OD stability

HDPE, PVC and PPR open their full line pages; precision tube and drinking straw open a delivered project. If your product sits between two rows, a material and a size are enough for us to name the layout.

Weighing two line types? Tell us the resin, the size band, the wall and where the pipe will be used, and we review the layout with you before anything is priced.

Chat With Maggie
02 / Line Categories

Pipe Extrusion Lines From Our Workshop

Seven line families cover most pipe and tube products. Each starts from a proven layout, then we resize it to your material, diameter, wall thickness, output and end use.

HDPE pipe extrusion line operating in a spacious factory with black plastic pipes stacked in the foreground A complete PVC pipe extrusion line with extruder and downstream units installed in a spacious factory, with finished plastic A complete plastic pipe extrusion line with control cabinets and stacked pipes inside a spacious, well-lit factory MPP cable protection pipe production Plastic pipe extrusion line installed in a factory workshop Tube extrusion equipment and connected downstream units in a workshop A complete flexible hose extrusion line with multiple connected units and control panels installed in a clean, well-lit Plastic extrusion line with downstream equipment installed in a brightly lit factory workshop White pipe sample held beside an extrusion line
HDPE / PE Pipe Extrusion Line
01

HDPE / PE Pipe Extrusion Line

Gas, water supply, irrigation, cable duct and PE pressure pipe

PE pipe is judged on two things that must last through a long run: an even wall and a round section. Every unit is sized to your diameter, from the single screw extruder and pipe die through vacuum calibration, spray cooling and the haul-off to a cutter or winder. A color stripe co-extruder is an add-on for markets that want one.

Explore HDPE / PE Line
02

PVC Pipe Extrusion Line

Drainage, pressure pipe, electrical conduit, rigid PVC

PVC pipe is only as good as its plasticizing and its surface, so we begin with your formulation and filler ratio. A PVC mixing system feeds the twin screw extruder, then the pipe die and vacuum calibration, the haul-off and the cutter. For socketed pipe, an automatic belling machine forms the joint end before the pipe leaves the line.

Explore PVC Line
03

PPR Pipe Extrusion Line

Single layer, multi layer or glass fiber pipe for hot and cold water

Installers notice quickly when PPR changes in outside diameter or weight from one meter to the next. The line pairs a stable die with matched cooling, a haul-off and a cutter. Co-extrusion is added when the pipe is multi layer or reinforced with glass fiber, and an online printer can mark your brand while the pipe runs.

Explore PPR Line
04

MPP Pipe Extrusion Line

Thick wall, PP based pipe that protects power cable

A heavy MPP wall needs long cooling and a firm pull, so those two stations decide whether the line keeps up. A high output extruder feeds a die sized to your wall thickness. An extended cooling section keeps the pipe round, the haul-off grips it without slipping, and the cutter stays accurate at full output.

05

Precision Tube Extrusion Line

Industrial, electronic, and pneumatic tight tolerance tube

When OD and ID tolerances are tight, drift has to be caught while the tube is still moving. A precision extruder and die feed the vacuum sizing tank, followed by cooling. Next, a laser gauge reads the diameter in line, and a steady haul-off with a controlled winder makes each reel match the last.

View Case Study
06

Medical Catheter Tube Extrusion Line

Catheter tube and medical tubing, clean operation

For catheter and medical tubing, the paperwork matters as much as the tube. The line combines a precision extrusion system, a medical tube die and online measurement. A steady melt and haul-off keep dimensions repeatable, winding is controlled, and validation support documents come with the line for your quality file.

07

Flexible Hose Extrusion Line

Flexible tube and hose in soft PVC, PE, PP or TPU

A good hose bends without kinking and still looks clean, and both depend first on the screw. We design it around your compound, then add a hose die, a cooling tank, the haul-off and a cutter or winder. Clarity, surface finish and kink resistance are tuned to your product, and a multi layer version is available.

08

Small Tube / Drinking Straw Line

Small diameter tube, drinking straw, lightweight tube

Drinking straws and small tube make money on line speed and clean cuts. A small tube extrusion system with a precision die runs through cooling into a high speed haul-off. Each piece is cut to your length, and an automatic collection system gathers the output. You choose the material and the diameter.

View Case Study
09

Core Tube Extrusion Line

Film, tape, label, paper and textile winding cores

Converters want cores that are straight, stiff and identical from one tube to the next, made at a material cost that still leaves a margin. Stable extrusion and a matched core tube die set the size, cooling holds the ID and OD, and a controlled haul-off and cutter keep each core straight and cut to length.

1 / 9

None of the nine is sold as a fixed package. Your material, pipe size and wall thickness, plus output target and voltage, set the final machine list, and we agree it with you before the quote.

Not Sure Where Your Pipe Fits?

Tell Us The Pipe, We Draft The Line

List the material, the diameter range, the wall thickness and your output target, and say what the pipe is for. You get a suggested line layout with the main machines and the reasons behind each one.

03 / Choose Your Line

Nine Decisions That Shape Your Pipe Line

Material, size, wall, output, end use and your own workshop decide what the line needs. Settle these nine points first and the quotes you receive become comparable.

White and pale-green plastic pellets in material bags 01

Pipe Material

PVC, PE, PP, PPR, TPU and medical grade compounds behave differently in the barrel, so one system cannot serve them all. Name your material first; the screw is chosen from it.

Sets: extruder type, screw design, feeding, temperature

Black HDPE pipe lengths at the end of an extrusion line 02

Pipe Diameter Range

Small tube, mid-size pipe and large diameter pipe load the die and the cooling in different ways. The size band you make fixes how big each downstream machine must be.

Sets: haul-off size, cooling, vacuum tank, calibration, pipe die

White pipe sample held beside an extrusion line 03

Wall Thickness Or SDR

The heavier the wall, the more cooling and the steadier the pull it needs. Skimp on either and the pipe sags or goes out of shape at full output.

Sets: line speed, haul-off force, cooling capacity, die design

Stacks of coiled plastic pipes wrapped in clear packaging film are arranged in a warehouse setting 04

Final Application

Each end use has its own critical point; a water pipe, a conduit, a medical tube, a hose and a core tube all fail in different ways. The application shows which part of the line needs most care.

Sets: line layout, online control, downstream, inspection points

White pipe passing through an orange downstream cutting machine 05

Output Target

The kg/h figure on an extruder model is a ceiling, not a promise. Whether you reach it with good pipe depends on the pipe size and the cooling that follows.

Sets: extruder size, motor power, downstream speed, cooling length

Pipe extrusion die head and connected tooling in a workshop 06

Single Or Multi Layer

Every extra layer, stripe or reinforcement means another co-extruder and a more complex die. Decide on it before the layout is drawn, not after.

Sets: co-extruder, dosing, multi layer die, layer control

Black plastic tubing being wound into a coil with finished coils in the background 07

Coil Or Straight Pipe

Small flexible pipe is normally coiled, while rigid pipe is cut to length and stacked. That choice decides every machine after the haul-off.

Sets: winder, cutter, stacker, pipe support, collection

Blue pipe positioned in a belling machine 08

Socket Or Plain End

Many PVC drainage and conduit buyers want a socket on one end so lengths push together without couplers. Belling sits right after the cutter, so it belongs in the first layout.

Sets: socket mold, heating, belling machine, line connection

Plastic pipe extrusion line installed in a factory workshop 09

Factory Conditions

Local voltage, floor space, water and compressed air, and the experience of your operators all affect installation and daily running. The electrical design and layout follow your plant.

Sets: electrical design, layout, auxiliaries, spares, training

You do not need all nine answers to start. Each one you can confirm narrows the machine list and makes our quotation more exact.

04 / Line Configurations

Standard Line Layouts By Pipe Type

From feeding to the last stacker, each pipe type has its own machine order. Pick a line to see the flow, the key machines, the options and what we confirm before quoting.

HDPE pipe extrusion line operating in a spacious factory with black plastic pipes stacked in the foreground HDPE / PE Line

Line Flow

Raw material feeding, then the single screw extruder with an optional color stripe co-extruder, the pipe die head, vacuum calibration and spray cooling tanks, haul-off, a cutter or winder, and the stacker.

Best For

PE pressure pipe, plus pipe for irrigation, gas, cable duct and water supply.

Key Equipment

A single screw extruder and pipe die, a vacuum calibration tank and a cooling tank, the haul-off, and a cutter or winder.

Optional Setup

Chipless cutter, automatic winder, a co-extruder for color stripes, online diameter measurement, handling for large diameters.

Confirm Before Quotation

Wall thickness or SDR, the diameter range, output, coiled or straight pipe, pipe length, and your workshop layout.

Please Note

Compare The Whole Line, Not The Extruder

Two quotes with the same extruder can make very different pipe. The die, calibration, cooling, haul-off and cutter decide the result, so check every machine on the list.

Chat With Maggie
05 / Machines In The Line

Every Machine In Your Pipe Line

Order the complete line, or add single machines to the line you already run. Each machine has its own page with sizes, options and the points to confirm before you buy.

06 / Problems To Avoid

Where Pipe Lines Usually Go Wrong

Most pipe defects start after the extruder: a die that does not suit the material, cooling that runs short, a haul-off that slips, or a cutter that cannot keep up. We check each one before we send a configuration.

Cross section showing uneven pipe wall thickness
Issue 01

Wall Thickness Variation

What happens An uneven wall wastes resin, pushes pipe weight off target and makes steady running difficult.

How we handle it We size the die, calibration sleeve and vacuum tank together with haul-off and line speed, from your diameter, wall and output. Tight specs get online wall thickness control.

White pipe extrusion downstream equipment installed on a workshop floor
Issue 02

Ovality And Poor Cooling

What happens The pipe leaves the tank oval or sagging, or loses its shape as soon as line speed goes up.

How we handle it On medium and large PE or MPP pipe, the vacuum and cooling tanks and the haul-off are fixed only after we have checked size, wall, cooling time and your floor space.

PVC pipe surface quality inspection
Issue 03

PVC Black Spots And Yellowing

What happens Black specks, yellow discoloration, a rough bore, unsteady output, or cracked sockets.

How we handle it The twin screw, die, cooling and any belling machine are chosen only after your compound, filler ratio, pipe size, standard and socket requirement are clear.

Extrusion line running at full output
Issue 04

Output Lower Than Expected

What happens The quoted output never arrives at stable quality, or it falls away after a size change.

How we handle it Output is discussed per material and per pipe size. Extruder, die, cooling, haul-off and the cutter or winder are then sized as one set, so the figure holds in production.

White pipe passing through an orange downstream cutting machine
Issue 05

Cutting, Winding Or Belling Problems

What happens Ragged cut ends, uneven coils, or PVC sockets that come out misshapen.

How we handle it First we settle how the pipe finishes: cut straight, coiled, stacked or belled. The cutter, winder, stacker or belling machine is then sized for full line speed.

Black HDPE pipe lengths at the end of an extrusion line
Issue 06

Wrong Line For The Final Pipe

What happens The machines work, yet the pipe misses its application, its market or the quality you were aiming for.

How we handle it The end use comes first in our review, whether that is gas, water, irrigation, drainage, conduit, PPR, MPP, hose, small tube, core tube or medical.

Technician checking an open machine control cabinet with a laptop
Issue 07

Difficult Installation And Start Up

What happens The machines reach your site, then wiring, first runs and operator training take far longer than planned.

How we handle it We supply the layout, installation guidance, a usable manual, spare parts advice and help with trial runs. Commissioning is done remotely or on site, whichever suits the project.

Full line configuration list and quotation
Issue 08

Incomplete Quotation Scope

What happens A cheap offer turns expensive once you find auxiliaries, downstream machines, testing or installation preparation left out.

How we handle it Our list follows your spec and names every stage: extrusion and die, calibration and cooling, haul-off, cutting or winding, stacking, belling, and auxiliary options.

Before You Ask For Prices

Let Us Check The Weak Points First

Before you compare prices, send the pipe material, size range, wall, target output and end use. We flag the machines that would limit your line before any price is quoted.

Chat With Maggie
07 / Material And Application

Match The Line To Your Pipe Material

A PVC conduit, an HDPE pressure pipe, a PPR hot water pipe, a flexible hose and a medical tube each put the strain on a different part of the line. The table shows where the equipment focus goes for each material.

Pipe Type Main Material Typical Application Equipment Focus What To Check
HDPE / PE Pipe HDPE, PE80, PE100 Water supply, gas, irrigation, cable duct Pipe die on a single screw extruder, vacuum calibration, cooling, haul-off Wall thickness and SDR, ovality, cooling length, winder or cutter
PVC Pipe PVC powder compound Drainage, pressure pipe, electrical conduit PVC mixing, twin screw extrusion, pipe die, calibration, belling Filler ratio, formulation, surface finish, cut quality, socket shape
PPR Pipe PP-R Hot and cold water pipe OD control, single screw extrusion, cooling, optional multi layer Pipe weight, OD tolerance, surface gloss, layer structure, printing
MPP Pipe Modified PP Power cable protection pipe Extended cooling, thick wall die, strong haul-off, accurate cutting Pipe roundness, wall thickness, rigidity, cut length, cooling capacity
Precision Tube PE, PP, PA, PU, PVC Industrial small tube, pneumatic tube, electronic tube Laser measurement, precision die, stable haul-off, controlled winding Concentricity, OD and ID tolerance, winding tension, traction stability
Medical Tube PVC, PU, TPU, PE, PP Catheter tube and medical tubing Online measurement, precision extrusion, clean operation, documentation support Dimensional control, material compatibility, repeatability, clean processing
Flexible Hose Soft PVC, TPU, PE, PP Appliance hose, garden hose, industrial hose Hose die, screw matched to the material, cooling, winding control Flexibility, transparency, anti kink performance, surface finish
Small Tube / Straw PP, PLA, applicable materials Small tube and drinking straw production Precision cutting, high speed small tube extrusion, automatic collection Material choice, local requirements, diameter, cut length, production speed
Core Tube PP, PE, PVC Winding core for film, tape, label, packaging Core tube die, stable extrusion, cooling, accurate cutting, strong haul-off Straightness, rigidity, ID and OD stability, material cost, cut accuracy

Give us the pipe type and the material, and the configuration is weighted toward what that pipe needs most.

Material Not In The Table?

Send A Drawing Or A Sample Photo

A drawing, a photo of a sample or a basic spec is enough. We check which extrusion and downstream setup suits it and tell you before you request a quote.

Chat With Maggie
Verification of conformity document bearing the name Zhangjiagang Qinxiang Machinery Co., Ltd.

CE Certified

EU market compliant

08 / CE Certificate

CE Certified Lines For The European Market

A line sold into Europe needs a real CE certificate and technical file behind it, or it can be held at customs, refused by inspectors or left off your insurance. We build to CE requirements and supply the documents with your order.

  • Built and documented to CE requirements for import into the EU
  • Your order ships with the certificate and technical file
  • Guarding, wiring and marking set up for your market
CE EU Compliant Documented
09 / Quality Control

Pipe Quality Checks By Line Type

Pick a pipe type to see what buyers measure and how we set the line up to hold it: diameter, wall, surface, cutting, winding and belling, over a long production run.

HDPE / PE Pipe

What Buyers Judge The Pipe On

  • Outside diameter holds steady
  • Wall thickness stays consistent
  • Ovality kept in check
  • Smooth pipe surface
  • Color stripe in the right spot
  • Accurate cutting length
  • Clean coil quality on small pipe
  • Quality holds on a long run

How we configure On PE pipe, five stations have to work as one: die head, vacuum calibration, the cooling length, haul-off and the cutter or winder. For medium and large diameters, cooling is sized from your diameter, wall and line speed, which keeps the pipe round at full output.

PVC Pipe

What Buyers Judge The Pipe On

  • Stable extrusion quality
  • Smooth outer surface
  • Smooth inner wall
  • Clean cutting edge
  • Socket keeps its shape
  • Black spots kept down
  • Low yellowing risk
  • Clear pipe marking

How we configure The finished PVC pipe reflects the twin screw, the formulation and temperature control, the die design, vacuum calibration and, where used, the belling unit. We agree your formula, filler ratio, pipe size, socket requirement and target output before configuring anything.

PPR Pipe

What Buyers Judge The Pipe On

  • OD tolerance held
  • Pipe stays round
  • Consistent pipe weight
  • Good surface gloss
  • Consistent color
  • Solid layer bonding
  • Clean cutting end
  • Clear printing

How we configure PPR water pipe relies on steady extrusion, tight OD control, enough cooling and a clean cut. When the pipe is multi layer or glass fiber reinforced, layer structure and bonding stability are settled first, and the line is chosen after.

Precision / Medical Tube

What Buyers Judge The Tube On

  • OD and ID tolerance
  • Concentricity held
  • Stable tube wall
  • Clean operation
  • Online measurement
  • Controlled winding tension
  • Batch to batch repeatability
  • Documentation support

How we configure Here, speed comes second to consistency. The line needs a steady melt flow, close control at the die, an accurate haul-off, controlled winding and online measurement, and we prepare validation documents when the project requires them.

Flexible Hose / Small Tube

What Buyers Judge The Product On

  • Stable diameter
  • Smooth surface
  • Flexibility
  • Transparency when needed
  • Accurate cutting length
  • Steady winding tension
  • Reliable auto collection
  • Material compatibility

How we configure Hose, small tube and straws depend on a screw designed for the compound, a matching die, then cooling, haul-off, the cutter and a collection system, each sized to the tube diameter, the production speed and the way finished product is handled.

Core Tube

What Buyers Judge The Tube On

  • Stable inner diameter
  • Stable outer diameter
  • Straightness
  • Rigidity
  • Cutting accuracy
  • Flat cutting end
  • Material cost kept down
  • Stable continuous output

How we configure Here the checks are rigidity, straightness and a steady ID and OD, with material cost kept in view. The haul-off and cutter are sized to your tube size, wall thickness and cut length.

White pipe sample held beside an extrusion line
1 / 6
Before Shipment

Trial Run Against Your Pipe Spec

Before the line ships, we run it against the pipe specification you approve and prepare sample pipe, inspection points or a video of the line running, depending on the project.

10 / Factory Capability

From Workshop Assembly To Container Loading

Machining, assembly, cabinet wiring, trial runs, sample pipe, spare parts and export packing happen under one roof in Zhangjiagang. The photos follow a line along that path, from the assembly bay and cabinet wiring through trial runs and sample checks to container loading, with installation support carrying it on to start-up at your plant.

Two workers assembling a large extruder barrel and gearbox on a factory floor with tools and posters visible
Four orange and white extrusion machines are lined up in a spacious factory workshop with an overhead crane visible
Four large high speed mixer units with control panels and discharge chutes installed in a factory workshop
Large metallic PVC die head with segmented heating zones mounted on a white support frame in a factory setting
Several profile extrusion lines with vacuum cooling tanks and control panels are arranged in a bright, spacious factory
Large wooden crate placed on a factory workshop floor with windows and industrial equipment in the background
Chat With Maggie
11 / Project Process

Your Pipe Line Project, Step By Step

From the first review of your pipe spec to start-up in your plant, each step has a clear output, so nothing is missing when the line arrives.

01White pipe sample held beside an extrusion line

Requirement Review

You send the pipe material and type, size range, wall thickness or SDR, output target, end use, voltage and floor space.

02A plastic extruder body with barrel heaters and cooling fans installed in a factory workshop setting

Line Configuration

We select the extruder, die, calibration and cooling for your pipe, then each downstream unit (cutter, winder, stacker, belling) and the auxiliaries.

03Technical proposal document

Technical Proposal

Our proposal lists the configuration with main parameters, a layout reference, power demand, options, test scope, delivery schedule and warranty terms.

04Two workers assembling a large extruder barrel and gearbox on a factory floor with tools and posters visible

Manufacturing And Assembly

Machining, assembly, control cabinet wiring, electrical integration and downstream matching are all done in our own workshop.

05Blue plastic pipe exiting machinery with rollers and pipe handling units on a factory floor

Trial Run Before Shipment

We run the line against the spec you signed off. Depending on the project, you receive photos of sample pipe, running videos or FAT details.

06Multiple industrial machines wrapped in plastic film and secured with orange straps inside a shipping container

Packing And Loading

Export packing covers machines, spare parts and paperwork. You receive loading photos, the packing list, the manual and shipping documents.

07Open machine control cabinet with drives, breakers and wiring

Installation And Training

Your team gets layout guidance and a wiring reference, help with installation and commissioning, and operator training through to start-up.

08Multiple plastic extrusion machines with hoppers and control panels lined up in a factory setting

After Sales Support

Once the line is running, we help with troubleshooting, spare parts, operating questions, maintenance and set-up changes for new pipe sizes.

Planning Or Expanding?

Walk Through The Project Before You Order

Planning a new line or adding capacity? Send your pipe spec, output target and workshop conditions, and we go through the project steps with you before quotation.

Chat With Maggie
12 / Projects And Trial Runs

Pipe Lines We Have Built And Tested

Recent pipe line projects, factory trial runs and finished samples, each configured to its material, size range, output and end use.

Pipe Diameter Range

16mm to 1200mm

PVC lines run 16 to 630mm, HDPE lines 20 to 1200mm and PPR lines 16 to 160mm; each project sits in the band its pipe needs.

Band 01 16 to 110mm
Band 02 110 to 250mm
Band 03 250 to 400mm
Band 04 400 to 630mm
Band 05 630 to 1200mm
A complete HDPE pipe extrusion line with extruder and calibration tank installed in a spacious factory with large windows Project 01

HDPE Irrigation Pipe Line

20 to 1200mm PE100

Line Setup

A single screw extruder plus color stripe co-extruder, vacuum and cooling tanks, haul-off, cutter and winder.

Project Focus

Irrigation pipe with an even wall, dependable cooling and neat coils.

View Case Study
A complete PVC pipe extrusion line with extruder and dosing system set up inside a spacious industrial workshop Project 02

PVC Drainage Pipe Line

16 to 630mm PVC Compound

Line Setup

Pipe die on a twin screw extruder, a vacuum calibration tank, haul-off and cutter, with an automatic belling machine.

Project Focus

Drainage pipe with a smooth surface, consistent sockets and clean cuts.

View Case Study
A complete PPR pipe extrusion line with extruder and downstream units installed in a spacious factory with green flooring Project 03

PPR Hot And Cold Water Pipe Line

16 to 160mm PP-R

Line Setup

Single screw extruder with PPR pipe die, vacuum calibration and a cooling tank, then haul-off, cutter and printer.

Project Focus

Water pipe held to a steady OD and an even weight, with a smooth finish.

MPP power cable protection pipe line Project 04

MPP Cable Protection Pipe Line

Modified PP

Line Setup

High output extruder feeding a thick wall pipe die, with vacuum calibration, extended cooling, a strong haul-off and the cutter.

Project Focus

Cable protection pipe that keeps a stable thick wall and a round section, with enough cooling capacity and accurate cuts.

Plastic pipe extrusion line installed in a factory workshop Project 05

Precision Tube Extrusion Line

Custom Small OD PE / PP / PA / PU

Line Setup

Tube die on a precision extruder, vacuum sizing and a cooling tank, a laser gauge for diameter, then a precision haul-off and the winder.

Project Focus

Precision tube held to OD and ID tolerance and concentricity, with steady traction and controlled winding.

View Case Study
A complete plastic extrusion line with control cabinets and downstream units installed in a bright factory setting Project 06

Medical Catheter Tube Line

Custom Tubing PVC / PU / TPU / PE / PP

Line Setup

Medical tube die on a precision extruder, the cooling system, online measurement, a stable haul-off and controlled winder.

Project Focus

Medical tubing made to controlled dimensions, cleanly and repeatably, with documentation support.

A complete PE core pipe extrusion line with control cabinets and downstream units installed in a spacious, well-lit factory Project 07

Core Tube Extrusion Line

Custom ID And OD PP / PE / Recycled

Line Setup

An extruder with core tube die, the cooling system, a strong haul-off, an accurate cutting system and stacking.

Project Focus

Winding cores for film, tape, label and textile use, kept straight and rigid with a stable ID and OD and accurate cuts.

Your own pipe spec is the starting point for each of these lines. Tell us the material, a diameter between 16mm and 1200mm and the output you need, and the line is built to match.

Project Feedback

What Pipe Producers Say

Feedback from factory owners and importers running our pipe extrusion lines, from configuration review to stable production.

Pipe extrusion line running at a buyer factory
Configuration Review Trial Run Confirmed

We compared several suppliers before placing the order. What stood out was the configuration review before quotation. The line matched our pipe sizes well, and the trial run let us confirm everything before shipment. Installation was smooth, and the line reached stable operation quickly.

PP

Pipe Producer, Southeast Asia

Multi Size Pipe Line

Complete Line Downstream Included

We wanted a complete pipe extrusion line, not separate machines. The configuration covered everything we needed, from the extruder to the downstream. Communication stayed clear through the project, and the sample pipe from the trial run matched what we expected.

FO

Factory Owner, Europe

Turnkey Pipe Line

Wall Consistency Recommissioned

Our old line struggled with wall thickness consistency. The configuration focused on cooling, haul off, and die matching instead of just pushing output higher. After commissioning, the pipe quality got a lot more stable across different sizes.

PM

Plant Manager, North America

Line Upgrade

First Project Full Support

This was our first pipe extrusion project, so we had a lot of technical questions. The layout suggestions, operation guidance, and commissioning support made it much easier. We got practical recommendations instead of just being handed a standard machine.

NB

New Pipe Producer, Southeast Asia

First Line Setup

13 / Quotation Checklist

What To Send For An Accurate Quote

A few basics are enough for a first configuration. A complete technical file can come later.

Start with the five main details. The optional ones bring the first configuration closer to final, but none of them is required to begin.

Chat With Maggie

Step 1

Main Details To Share

  • Material: PVC, HDPE, PE, PPR, PP, MPP, TPU or another resin
  • Pipe diameter range
  • Wall thickness or SDR
  • Final pipe application
  • Target output, in kg/h or m/min

Optional

Helpful If Available

  • Single layer or multi layer structure
  • Cutter, winder, stacker or belling machine required
  • Voltage and frequency
  • Workshop space
  • Pipe drawing, sample photo, or short video

Missing a few answers? Send the ones you have, and we work through the gaps with you and confirm the configuration one point at a time.

14 / FAQ

Pipe Extrusion Line Questions

What buyers ask us most about choosing, setting up and running a pipe line. If yours is not here, ask Maggie directly.

Let the material and the end use decide. HDPE and PE lines mostly serve water supply, gas, irrigation and cable duct. PVC lines process PVC powder on a twin screw extruder for drainage, pressure pipe and conduit. PPR lines are built mainly for hot and cold water pipe, in single or multi layer form or reinforced with glass fiber.

Yes, within a range. Each size change means swapping molds and calibration sleeves and resetting the downstream machines. When the range is very wide, small and large pipe need such different cooling, haul-off and cutting that two separately planned lines can make more sense.

Judge it against the material, the pipe diameter, the wall thickness and the cooling capacity; the extruder model alone says little. Output holds only when the extruder and die, vacuum calibration and cooling tank, and haul-off and cutter or winder are sized together, so pipe at your size runs without stops.

Five things: die design, melt pressure, vacuum calibration, how well the haul-off is synchronized, and line speed. That is why diameter, material, wall thickness or SDR and the output target are reviewed as one set before we propose a line.

For PVC pipe, as a rule. PVC powder compound has to be plasticized evenly, mixed properly and held at an accurate temperature, and a twin screw does that well. PE, PPR, PP and TPU, like many flexible materials, normally run on a single screw, though the product structure and the way the material behaves can change that.

It depends on line speed, material, diameter and pipe length, and on whether you coil the pipe or cut it straight. The options run from vacuum calibration and cooling tanks, haul-off, cutter and winder to stacker, belling machine, printer, co-extruder and online measurement.

Roundness, a stable OD, surface quality and the speed you can hold over a long run all depend on them. On medium and large PE or MPP pipe, the cooling length has to suit pipe size, wall thickness and planned output; when it falls short, the pipe goes oval and deforms.

Yes, with additional co-extruders and a die designed for the structure, which applies to stripes, multiple layers and reinforced pipe alike. We first confirm the pipe structure, layer material, number of stripes, diameter and target application.

Repeatability and dimensional control, ahead of output. In practice that means tight OD and ID tolerance, concentricity, steady traction, clean operation, online measurement and controlled winding.

The core five are material, diameter range, wall thickness or SDR, end use and expected output. A drawing or sample photo, the layer structure, your voltage, the workshop space and the downstream method you prefer all make the proposal more precise.

15 / Configuration Request

Start Your Pipe Line Project With Maggie

New line, upgrade of an existing one, or still choosing between options: send whatever you have. Maggie answers in person within 24 hours with concrete configuration details and the next step.

Maggie, QinX Machinery sales and support contact

Maggie

Pipe Line Sales, QTech Machinery

Replies within 24 hours

I read every message sent from this form myself. Describe your pipe and the output you need, and you get a line configuration and a priced quotation back, not a catalogue.

A material and a pipe size, or simply a drawing, is enough to begin. Our pipe extrusion, granulating and recycling lines go to factories and importers in 60+ countries.

Maggie

Sales, Zhangjiagang Qinxiang Machinery Co., Ltd.

Configuration Request

Tell Us About Your Pipe Line Project

Fields marked are required.

Details stay private No sales spam Maggie replies in person